Page 2 - Demo

OIKOS S.P.A. a socio unicoVia Cherubini, 2 47043 Gatteo Mare (FC)info@oikos-group.itITALIAtel. +39 0547.681412INTERNATIONALtel. +39 0547.681460TECHNICAL DATA SHEET tr/10FinishTRAVERTINO ROMANO Natural/White with Travertino Romano FinituraTo protect and keep the natural look of TRAVERTINO ROMANO Natural White , apply by brush, a coat of uncoloured, ready to use TRAVERTINO ROMANO FINITURA.TRAVERTINO ROMANO Natural/White with TONER (Tivoli, Biancospino and so on):Apply by brush a coat of uncoloured, ready to use TRAVERTINO ROMANO FINITURA paySpecificationsSurfaces must be thoroughly dry and fully matured. New plaster must have matured for at least 30 days to allow the full carbonatation of the substrate. Clean the surface to be coated, be used, applying the product undiluted with a synthetic sponge so as to increase the intensity of the colour in the finish. Effect METROPOLITANO: Apply TRAVERTINO ROMANO in the same way as for the previous effect creating diagonal veins across the surface. Once dry, apply OTTOCENTO undiluted using a synthetic sponge applying the product only on the flat, smooth areas and not in the veins. Effect PIETRA ANTICA: After having realized the previously described finishes, it is possible to recreate the joints between the various stones. Cut the surface of the TRAVERTINO ROMANO using the corner of a Small spatula by Oikos art. 111 (or a screwdriver) thus obtaining blocks of the desired dimension. To cut a straight line, use a plank as a guide. Leave for at least 24 hours to dry before proceeding with the finish.Effect GRANATO: Screed the wall with TRAVERTINO ROMANO without leaving too many imperfections. When dry, screed again evenly. Whilst the product is still moist scratch the surface with the corners on the back side of the trowel, then proceed to smooth the surface using the flat side of the trowel. Before the product is fully dry, repeat both the scratching and smoothing of the surface. Effect LEVIGATO: Screed the wall with TRAVERTINO ROMANO without leaving too many imperfections. Once dry, make one more fine screeding. As soon as the product starts to dry repeatedly smooth the surface with the flat side of the spatula.Effect CASSERO: Screed the surface with TRAVERTINO ROMANO. without leaving too many imperfections. When the product has dried, using masking tape, mark out a band approximately 10-13 cm wide. Using a trowel, apply TRAVERTINO ROMANO along the entire band, then immediately proceed to work over the surface using the tool Attrezzo Legnato (art. 109) in order to create wood-like veins. As soon as the product starts to dry, smooth the surface using the flat side of the trowel. When completely dry, remove the tape and proceed to work on the next band. The application can also be made simultaneously on alternate bands. In order to get a more compact effect we suggest to make TRAVERTINO ROMANO denser by using O-Addensante (1 50 ml bottle of O-Addensante for 20 kg of product).NoteThe company Oikos Spa guarantees, to the best of its own technical and scientific knowledge, that the information contained in this technical data sheet is correct. Notwithstanding that indicated above, Oikos takes no responsibility for the results obtained through the use of this product in as much as it is not possible for Oikos to check or control the application method used. For this reason, we recommend that you check carefully that each product chosen, is suitable for each individual use to which it is put. Safety informationThe product is free of heavy metals such as lead or chrome. It does not contain toxic solvents, aromatics or chlorides. There is no risk of any dangerous polymerisation. The product is classified as hazardous pursuant to the provisions set forth in the Regulations (CE) 1272/2008 (CLP) and subsequent amendments and supplements. For further information see the product Safety Data Sheet. Normal cautionary measures for the handling of water based paints are advised. No special arrangements are required for the storage, movement and transportation of the product; the containers, residue, eventual spilt material should be cleaned up using absorbent inert material such as sand, soil etc. etc. and then disposed of in accordance with the regional and national regulations in force at that time. Transportation must be carried out in accordance with international agreements.ing attention to spread the product only on the smooth areas of the surface and not inside the veins that have been created.Wait until the first coat of finish is dry and then proceed to apply a second coat, applying by brush TRAVERTINO ROMANO FINITURA in the chosen colour, diluted 50% with water. Eliminate any excess product using a sponge until a lightdark effect is achieved on the surface caused by the differing absorption levels between the smooth areas and the veins in the surface.To obtain the chosen shade from the colour chart, mix 100 ml of TONER with 1lt of TRAVERTINO ROMANO FINITURA and shake thoroughly.Attention: these finishes can be used only for the colour NATURAL WHITE, they cannot be used for the DESIGN shades (Black, Red, Beige, Grey, Yellow ) which are suitable only for interiors. Only for use in interiors:TRAVERTINO ROMANO with OttocentoIn order to have pearly veins it is possible to apply one or more shades of OTTOCENTO onto TRAVERTINO ROMANO following the instructions given in the section Application Method. The application is made by brush fading the product with a sponge.TRAVERTINO ROMANO DESIGN (Black, Red, Beige, Grey, Yellow, only for interiors)The finish with OTTOCENTO can be made for the DESIGN shades. TRAVERTINO ROMANO FINITURA SHOULD NOT be used. removing any loose or flaking material. On old or powdering surfaces, it is recommended to apply a coat of the sealer NEOFIX by Oikos. On all other types of surface, apply a coat of IL PRIMER by Oikos or of BLANKOR by OIKOS. Apply a lime based decorative product such as TRAVERTINO ROMANO to realize the decorative effect %u2026............ All must be carried out in accordance with the norms of application, at a cost of %u2026%u2026%u2026%u2026 m%u00b2 inclusive of materials and labour, except scaffolding.